SLURM/JobStatus: Difference between revisions

From UMIACS
Jump to navigation Jump to search
No edit summary
Line 10: Line 10:
Examples:
Examples:
<pre>
<pre>
username@opensub00:squeue -u username
username@nexusclip00:squeue -u username
             JOBID PARTITION    NAME    USER ST      TIME  NODES NODELIST(REASON)
             JOBID PARTITION    NAME    USER ST      TIME  NODES NODELIST(REASON)
               162    test2 helloWor username  R      0:03      2 openlab[00-01]
               162    test2 helloWor username  R      0:03      2 tron[00-01]
</pre>
</pre>


<pre>
<pre>
username@opensub00:squeue --start -u username
username@nexusclip00:squeue --start -u username
             JOBID PARTITION    NAME    USER ST          START_TIME  NODES SCHEDNODES          NODELIST(REASON)
             JOBID PARTITION    NAME    USER ST          START_TIME  NODES SCHEDNODES          NODELIST(REASON)
               163    test2 helloWo2 username PD 2020-05-11T18:36:49      1 openlab02           (Priority)
               163    test2 helloWo2 username PD 2020-05-11T18:36:49      1 tron02           (Priority)
</pre>
</pre>


<pre>
<pre>
username@opensub00:squeue -s -u username
username@nexusclip00:squeue -s -u username
         STEPID    NAME PARTITION    USER      TIME NODELIST
         STEPID    NAME PARTITION    USER      TIME NODELIST
           162.0    sleep    test2 username      0:05 openlab00
           162.0    sleep    test2 username      0:05 tron00
           162.1    sleep    test2 username      0:05 openlab01
           162.1    sleep    test2 username      0:05 tron01
</pre>
</pre>



Revision as of 23:41, 22 April 2022

Job Status

SLURM offers a variety of tools to check the status of your jobs before, during, and after execution. When you first submit your job, SLURM should give you a job ID which represents the resources allocated to your job. Individual calls to srun will spawn job steps which can also be queried individually.

squeue

The squeue command shows job status in the queue. Helpful flags:

  • -u username to show only your jobs (replace username with your UMIACS username)
  • --start to estimate start time for a job that has not yet started and the reason why it is waiting
  • -s to show the status of individual job steps for a job (e.g. batch jobs)

Examples:

username@nexusclip00:squeue -u username
             JOBID PARTITION     NAME     USER ST       TIME  NODES NODELIST(REASON)
               162     test2 helloWor username  R       0:03      2 tron[00-01]
username@nexusclip00:squeue --start -u username
             JOBID PARTITION     NAME     USER ST          START_TIME  NODES SCHEDNODES           NODELIST(REASON)
               163     test2 helloWo2 username PD 2020-05-11T18:36:49      1 tron02            (Priority)
username@nexusclip00:squeue -s -u username
         STEPID     NAME PARTITION     USER      TIME NODELIST
          162.0    sleep     test2 username      0:05 tron00
          162.1    sleep     test2 username      0:05 tron01

sstat

The sstat command shows metrics from currently running job steps. If you don't specify a job step, the lowest job step is displayed.

sstat --format JobID,NTasks,nodelist,MaxRSS,MaxVMSize,AveRSS,AveVMSize <$JOBID>.<$JOBSTEP>
username@opensub00: sstat --format JobID,NTasks,nodelist,MaxRSS,MaxVMSize,AveRSS,AveVMSize 171
       JobID   NTasks             Nodelist     MaxRSS  MaxVMSize     AveRSS  AveVMSize 
------------ -------- -------------------- ---------- ---------- ---------- ---------- 
171.0               1            openlab00          0    186060K          0    107900K 
username@opensub00: sstat --format JobID,NTasks,nodelist,MaxRSS,MaxVMSize,AveRSS,AveVMSize 171.1
       JobID   NTasks             Nodelist     MaxRSS  MaxVMSize     AveRSS  AveVMSize 
------------ -------- -------------------- ---------- ---------- ---------- ---------- 
171.1               1            openlab01          0    186060K          0    107900K 

Note that if you do not have any jobsteps, sstat will return an error.

username@opensub00: sstat --format JobID,NTasks,nodelist,MaxRSS,MaxVMSize,AveRSS,AveVMSize 172
       JobID   NTasks             Nodelist     MaxRSS  MaxVMSize     AveRSS  AveVMSize 
------------ -------- -------------------- ---------- ---------- ---------- ----------
sstat: error: no steps running for job 237

If you do not run any srun commands, you will not create any job steps and metrics will not be available for your job. Your batch scripts should follow this format:

#!/bin/bash
#SBATCH ...
#SBATCH ...
# set environment up
module load ...

# launch job steps
srun <command to run> # that would be step 1
srun <command to run> # that would be step 2

sacct

The sacct command shows metrics from past jobs.

username@opensub00:sacct
       JobID    JobName  Partition    Account  AllocCPUS      State ExitCode 
------------ ---------- ---------- ---------- ---------- ---------- -------- 
162          helloWorld      test2      staff          2  COMPLETED      0:0 
162.batch         batch                 staff          1  COMPLETED      0:0 
162.0             sleep                 staff          1  COMPLETED      0:0 
162.1             sleep                 staff          1  COMPLETED      0:0 
163          helloWorld      test2      staff          2  COMPLETED      0:0 
163.batch         batch                 staff          1  COMPLETED      0:0 
163.0             sleep                 staff          1  COMPLETED      0:0 

To check one specific job, you can run something like the following (if you omit .<$JOBSTEP>, all jobsteps will be shown):

sacct  --format JobID,jobname,NTasks,nodelist,MaxRSS,MaxVMSize,AveRSS,AveVMSize,Elapsed -j <$JOBID>.<$JOBSTEP>
username@opensub00:sacct  --format JobID,jobname,NTasks,nodelist,MaxRSS,MaxVMSize,AveRSS,AveVMSize,Elapsed -j 171
       JobID    JobName   NTasks        NodeList     MaxRSS  MaxVMSize     AveRSS  AveVMSize    Elapsed 
------------ ---------- -------- --------------- ---------- ---------- ---------- ---------- ---------- 
171          helloWorld           openlab[00-01]                                               00:00:30 
171.batch         batch        1       openlab00          0    119784K          0    113120K   00:00:30 
171.0             sleep        1       openlab00          0    186060K          0    107900K   00:00:30 
171.1             sleep        1       openlab01          0    186060K          0    107900K   00:00:30 

Job Codes

When you list the current running jobs and your job is in PD (Pending), SLURM will provide you some information on what the reason for this in the NODELIST parameter. You can use scontrol show job <jobid> to get all the parameters for your job which may be required to identify why your job is not running.

# squeue -u testuser
JOBID PARTITION     NAME     USER     ST       TIME  NODES NODELIST(REASON)
581530     dpart     bash    testuser PD       0:00      1 (AssocGrpGRES)
581533     dpart     bash    testuser PD       0:00      1 (Resources)
581534     dpart     bash    testuser PD       0:00      1 (QOSMaxGRESPerUser)
581535 scavenger     bash    testuser PD       0:00      1 (ReqNodeNotAvail, Reserved for maintenance)

Some common ones are as follows:

  • Resources - The cluster does not currently have the resources to fit your job.
  • QOSMaxGRESPerUser - The quality of service (QoS) your job is running in has a limit of resources per user. Use show_qos to identify the limits and then use scontrol show job <jobid> for each of your jobs running in that QoS.
  • AssocGrpGRES - The SLURM account you are using has a limit on the resources available in total for the account. Use sacctmgr show assoc account=<account_name> to identify the GrpTRES limit. You can see all jobs running under the account by running squeue -A account_name and then find out more information on each job by scontrol show job <jobid>.
  • ReqNodeNotAvail - If you have requested a specific node and it is currently scheduled you can get this job code. You can also get this job code when it provides Reserved for maintenance that there is a reservation in place (often for a maintenance window). You can see the current reservations by running scontrol show reservation. Often the culprit is that you have requested a TimeLimit that will conflict with the reservation. You can either lower your TimeLimit so that the job will complete before the reservation begins, or leave your job to wait until the reservation completes.